All about bicycles, pedelecs, technology and safety in the press

In our daily work as we deal with bicycle safety, technology and user manuals we come across lots of safety risks. The most frequent ones are published in articles of the leading German special-interest magazines TOUR – Europas Rennrad-Magazin Nr. 1, BIKE – Das Mountainbike Magazin Europas Nr. 1 and E-Bike – Das Pedelec-Magazin to make this information important for the sector accessible to a wider public.

For many years now the Eurobike Show Daily accompanying the annual international Eurobike Show has given us the opportunity to publish our perspective on major developments in the cycle industry in full-page articles.

We also speak regularly in independent lectures about all topics relating to bicycle technology and bicycle market. In addition, we are regularly cited by further special-interest magazines or trade journals as well as more and more by radio and television and in their media reports, which shows us that we are completely right with our information. The section NEWS informs you about the latest news from our specialist fields. The reports and publications of this section are listed chronologically or according to topics of interest.

News

BIKE 12/2015

Seat posts – That’s how we tested

FIELD TEST – The practical experiences were collected from various testers over several months. For this purpose each seatpost was mounted and ridden on the identical hardtail. Besides the riding experiences, details as to the mounting and handling of the seatpost were recorded. In spite of the subjective component of the field test and the great variation of the tester pool from 70 to 90 kg, the statements as to comfort are very homogenous. Safety-relevant anomalies or even failures were not registered.

LABORATORY TEST – The tests regarding the fatigue behaviour of the seatposts and their flex behaviour were conducted at the testing institute Zedler (www.zedler.de) in Ludwigsburg. First of all, each seatpost had to comply with the requirements of the ISO standard 4210. That included 100,000 load cycles of 1200 N applied behind the middle of the saddle clamp. Subsequently the test samples went through a practical test spectrum developed by the Zedler institute which introduces not only higher loads up to 1700 N, but also individual loads to the saddle nose. The loads are to simulate a useful life of the seat post over several years by a 90 kg cyclist during intensive tours. The chosen extension length was 27 cm, i.e. quite close to reality. More details at: www.bike-magazin.de (...).

Dirk Zedler, graduate engineer, bicycle expert

"Claims regarding seatpost failure are nearly regularly on the agenda of our daily routine of writing expert’s reports. There are basically three damage mechanisms. The most frequent one is the failure of the bolted connections. The movements of the saddle partly result in inappropriate load acting on them. In this case the reserve is inferior, already a slightly too low torque value can result in failure. Fractures in the area where the seatpost comes out of the frame are quite rare. This is particularly due to the too low compressive strength of carbon tubes and to unfavourable clamp mechanisms on the tubes. Often the clamps are overtightened on the tubes. The least common are fractures in the middle of the tube or at the head. During the operational strength test it was made sure to observe the torque values which did not tighten the seatposts in an unfavourable way or overtightened them.

The test criteria are above the ISO standard, as the minimum requirements of this standard do not include harder service. BIKE real data collections revealed that a cyclist is pressed into the saddle with an increase in the acceleration due to gravity when riding through a compression. An 80 kg cyclist brings about 50 kg on the saddle depending on his position, which corresponds to a short-term load of up to 2000 Newton. With our test loads we have remained clearly below."

If you want to read the entire article, order the respective issue from Delius-Klasing-Verlag or (if it is sold out) send us an addressed and pre-paid envelope (DIN A4) and 3.00 Euro in stamps together with a short note indicating which article you are interested in.

Go back

News

IHK Magazin – Wirtschaft 10.2019

Durch die Nutzung dieser Webseite erklären Sie sich mit der Verwendung von Cookies einverstanden. Detaillierte Informationen über den Einsatz von Cookies auf dieser Webseite erhalten Sie in der Datenschutzerklärung.

Standard

Tools, die wesentliche Services und Funktionen ermöglichen, einschließlich Identitätsprüfung, Servicekontinuität und Standortsicherheit. Diese Option kann nicht abgelehnt werden.

Analytik

Tools, die anonyme Daten über Website-Nutzung und -Funktionalität sammeln. Wir nutzen die Erkenntnisse, um unsere Produkte, Dienstleistungen und das Benutzererlebnis zu verbessern.

Drittanbieter-Inhalten

Auf dieser Webseite wird Inhalt über Drittanbieter bereitgestellt. Um diesen Inhalt erleben zu können wird Ihre Zustimmung benötigt. Hierbei werden Daten an den Drittanbieter übermittelt und Cookies gesetzt.